Ganga is using world class raw material of Reliance Industries Ltd, to Manufacturing of uPVC SWR: stands for 'Soil, Waste & Rain' drainage systems in India
SWR: stands for 'Soil, Waste & Rain'. SWR pipes are used for soil, waste and rain water management. These pipes are immune to bacteria, fungi, micro-organisms, rodent and insect attack. It enables fast and efficient removal of waste without blockage and leakage.
There are two types of SWR Pipes; Type A — for use in ventilation pipe work, rain water drainage, and rain water harvesting applications. Type B — for use in soil and waste discharge systems.
This standard covers requirements for plain and socket end unplasticized polyvinyl chloride ( UPVC ) pipes with nominal outside diameters 40 mm to 110 mm for use for soil and waste discharge system inside buildings including ventilating and rain water applications.
| Density [g/cm3] | 1.28 - 1.43 |
| Thermal conductivity[w/(m.k)] | 0.12 - 0.27 |
| Yield strength [MPa] | 30 - 60 |
| Young's modulus [psi] | 480000 |
| Flexural strength (yield) [psi] | 10000 |
| Compression strength [psi] | 9000 |
| Coefficient of thermal expansion (linear) [mm(mm"c)] | 5 x 10? |
| Vicat [°c ] | 65 - 100 |
| Resistivity [Qm] | 10¹? |
| Surface resistivity [Q] | 10¹³ - 10¹? |
The most widely used material in pipe installations is Unplasticised Polyvinyl Chloride. It can be used for both interior and exterior applications. Its chemical resistance is high and combined with its smooth bore there is virtually no build up of scale or residue and gives very good flow characteristics.
PVC-U is odourless and tasteless which makes it ideal for transporting foodstuffs and drinking water. It has high abrasion and weathering resistance.
Finally PVC-U gives good electrical and thermal resistance as well as being light and clean to handle and can be easily jointed.
PVC Conduit Pipes are 100% safe & durable. These pipes are Fire Retardant Low Smoke (FRLS), Corrosion Proof. Consistent in Physical & Electrical properties. Unaffected by weather conditions, Termite, Fungus etc.
The chemical resistance properties of PVC-U are excellent. It is resistant to most solutions of acids, alkalis, salts and solutions which can be mixed with water. PVC-U is not resistant to aromatic and chlorinated hydrocarbons
The permissable working temperature range for PVC-U is from 0-60oC. Pressure ratings of pipe and fittings are usually quoted at a temperature of 20oC. It can be used at higher temperature but there will be a corresponding drop in the maximum pressure allowed. This is a fundamental principle of plastic pipework.
The Solvent cement used for jointing PVC-U fittings and pipe need to be a gap filling cement with a thick consistency. Non Gap-filling cements MUST not be used. The cement creates a chemical bond between the pipe and fitting. It is a simple and effective method of jointing and as it is permanent it is important to follow the correct procedure
To ensure maximum service life from the pipe and fitting transporting all manner of substances it is important to use the most effective Cement avaliable. The cement which we use is DYTEX which will ensure maximum service life and a very high degree of resistance.
However prolonged exposure of the inside joint to any of the following acid concentrations may eventually lead to some deterioration of the cement bonding
Company delivering excellence products since 35 years is not a small achievement, it requires patience, talent, capabilities, and customer retention.
|
|
| Nominal Size | Mean Outside Diameter (mm) | Outside Diameter at Any Point (mm) | Wall Thickness,Type A (mm) | Wall Thickness,Type B (mm) | |||||
|---|---|---|---|---|---|---|---|---|---|
| (inch) | (mm) | Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. |
| 2½ | 75 | 75.0 | 75.3 | 74.1 | 75.9 | 1.8 | 2.2 | 3.2 | 3.8 |
| 3 | 90 | 90.3 | 90.3 | 88.9 | 91.2 | 1.9 | 2.3 | 3.2 | 3.8 |
| 4 | 110 | 110.0 | 110.4 | 108.6 | 111.4 | 2.2 | 2.7 | 3.2 | 3.8 |
| Nominal Size | Mean Outside Diameter (mm) | Outside Diameter at Any Point (mm) | Wall Thickness,Type A (mm) | Wall Thickness,Type B (mm) | |||||
|---|---|---|---|---|---|---|---|---|---|
| (inch) | (mm) | Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. |
| 1¼ | 40 | 40.0 | 40.3 | 39.5 | 40.5 | 1.8 | 2.2 | 3.2 | 3.8 |
| 1.5 | 50 | 50.0 | 50.3 | 49.4 | 50.6 | 1.8 | 2.2 | 3.2 | 3.8 |
| 2 | 63 | 63.0 | 63.2 | 62.2 | 63.8 | 1.8 | 2.2 | 3.2 | 3.8 |
| 2½ | 75 | 75.0 | 75.3 | 74.1 | 75.9 | 1.8 | 2.2 | 3.2 | 3.8 |
| 3 | 90 | 90.0 | 90.3 | 88.9 | 91.2 | 1.9 | 2.3 | 3.2 | 3.8 |
| 4 | 110 | 110.0 | 110.4 | 108.6 | 111.4 | 2.2 | 2.7 | 3.2 | 3.8 |
Ganga Piping Solutions Pvt Ltd warrants to the original owner that the product will be free from manufacturing defects and conform to the current applicable IS Standards under normal use. Buyer’s remedy for breach of this warranty is limited to replacement of, or credit for,the defective product. This warranty excludes any expense for removal or reinstallation of any defective product and any other incidental, consequential or punitive damages.WARRANTY APPLICABLE ONLY IF GANGA PIPES, FITTINGS & SOLVENT CEMENT ARE USED. Actual product may vary due to product enhancement. All product images shown are for illustration purposes only and may not be an exact representation of the product.Products and specifications subject to change without notice. |
